| SIMATIC S7-400, CPU 412-2 PN Central processing unit with: Work memory 1 MB, (0.5 MB code; 0.5 MB data) interfaces 1st interface MPI/DP 12 Mbit/s, (X1), 2nd interface Ethernet/PROFINET (X5) |
| General information |
| Product type designation | CPU 412-2 PN |
| HW functional status | 01 |
| Firmware version | V7.0 |
| Product function |
| ● Isochronous mode | Yes; Via PROFIBUS DP or PROFINET interface |
| Engineering with |
| ● Programming package | STEP 7 V5.5 or higher with HSP 262 |
| CiR - Configuration in RUN |
| CiR synchronization time, basic load | 100 ms |
| CiR synchronization time, time per I/O byte | 30 µs |
| Supply voltage |
| Rated value (DC) | Power supply via system power supply |
| Input current |
| from backplane bus 5 V DC, typ. | 1.1 A |
| from backplane bus 5 V DC, max. | 1.4 A |
| from backplane bus 24 V DC, max. | 150 mA; 150 mA per DP interface |
| from interface 5 V DC, max. | 90 mA; At the DP interface |
| Power loss |
| Power loss, typ. | 5.5 W |
| Power loss, max. | 7 W |
| Memory |
| Type of memory | RAM |
| Work memory |
| ● integrated | 1 Mbyte |
| ● integrated (for program) | 512 kbyte |
| ● integrated (for data) | 512 kbyte |
| ● expandable | No |
| Load memory |
| ● expandable FEPROM | Yes; with Memory Card (FLASH) |
| ● expandable FEPROM, max. | 64 Mbyte |
| ● integrated RAM, max. | 512 kbyte |
| ● expandable RAM | Yes; with Memory Card (RAM) |
| ● expandable RAM, max. | 64 Mbyte |
| Backup |
| ● present | Yes |
| ● with battery | Yes; all data |
| ● without battery | No |
| Battery |
| Backup battery |
| ● Backup current, typ. | 180 µA; up to 40 °C |
| ● Backup current, max. | 850 µA |
| ● Backup time, max. | Dealt with in the module data manual with the secondary conditions and the factors of influence |
| ● Feeding of external backup voltage to CPU | 5 V DC to 15 V DC |
| CPU processing times |
| for bit operations, typ. | 31.25 ns |
| for word operations, typ. | 31.25 ns |
| for fixed point arithmetic, typ. | 31.25 ns |
| for floating point arithmetic, typ. | 62.5 ns |
| CPU-blocks |
| DB |
| ● Number, max. | 3 000; Number range: 1 to 16000 |
| ● Size, max. | 64 kbyte |
| FB |
| ● Number, max. | 1 500; Number range: 0 to 7999 |
| ● Size, max. | 64 kbyte |
| FC |
| ● Number, max. | 1 500; Number range: 0 to 7999 |
| ● Size, max. | 64 kbyte |
| OB |
| ● Number, max. | see instruction list |
| ● Size, max. | 64 kbyte |
| ● Number of free cycle OBs | 1; OB 1 |
| ● Number of time alarm OBs | 2; OB 10, 11 |
| ● Number of delay alarm OBs | 2; OB 20, 21 |
| ● Number of cyclic interrupt OBs | 2; OB 32, 35 (shortest cycle that can be set = 500 µs) |
| ● Number of process alarm OBs | 2; OB 40, 41 |
| ● Number of DPV1 alarm OBs | 3; OB 55-57 |
| ● Number of isochronous mode OBs | 2; OB 61-62 |
| ● Number of multicomputing OBs | 1; OB 60 |
| ● Number of background OBs | 1; OB 90 |
| ● Number of startup OBs | 3; OB 100-102 |
| ● Number of asynchronous error OBs | 9; OB 80-88 |
| ● Number of synchronous error OBs | 2; OB 121, 122 |
| Nesting depth |
| ● per priority class | 24 |
| ● additional within an error OB | 1 |
| Counters, timers and their retentivity |
| S7 counter |
| ● Number | 2 048 |
| Retentivity |
| — adjustable | Yes |
| — preset | Z 0 to Z 7 |
| Counting range |
| — lower limit | 0 |
| — upper limit | 999 |
| IEC counter |
| ● present | Yes |
| ● Type | SFB |
| ● Number | Unlimited (limited only by RAM capacity) |
| S7 times |
| ● Number | 2 048 |
| Retentivity |
| — adjustable | Yes |
| — preset | No times retentive |
| Time range |
| — lower limit | 10 ms |
| — upper limit | 9 990 s |
| IEC timer |
| ● present | Yes |
| ● Type | SFB |
| ● Number | Unlimited (limited only by RAM capacity) |
| Data areas and their retentivity |
| Retentive data area (incl. timers, counters, flags), max. | Total working and load memory (with backup battery) |
| Flag |
| ● Size, max. | 4 kbyte; Size of bit memory address area |
| ● Retentivity available | Yes |
| ● Retentivity preset | MB 0 to MB 15 |
| ● Number of clock memories | 8; in 1 memory byte |
| Local data |
| ● adjustable, max. | 8 kbyte |
| ● preset | 4 kbyte |
| Address area |
| I/O address area |
| ● Inputs | 4 kbyte |
| ● Outputs | 4 kbyte |
| Process image |
| ● Inputs, adjustable | 4 kbyte |
| ● Outputs, adjustable | 4 kbyte |
| ● Inputs, default | 128 byte |
| ● Outputs, default | 128 byte |
| ● consistent data, max. | 244 byte |
| ● Access to consistent data in process image | Yes |
| Subprocess images |
| ● Number of subprocess images, max. | 15 |
| Digital channels |
| ● Inputs | 32 768 |
| — of which central | 32 768 |
| ● Outputs | 32 768 |
| — of which central | 32 768 |
| Analog channels |
| ● Inputs | 2 048 |
| — of which central | 2 048 |
| ● Outputs | 2 048 |
| — of which central | 2 048 |
| Hardware configuration |
| Number of expansion units, max. | 21 |
| connectable OPs | 47 |
| Multicomputing | Yes; 4 CPUs max. (with UR1 or UR2) |
| Interface modules |
| ● Number of connectable IMs (total), max. | 6 |
| ● Number of connectable IM 460s, max. | 6 |
| ● Number of connectable IM 463s, max. | 4; IM 463-2 |
| Number of DP masters |
| ● integrated | 1 |
| ● via CP | 10; CP 443-5 Extended |
| ● via IM 467 | 4 |
| ● Mixed mode IM + CP permitted | No; IM 467 cannot be used jointly with CP 443-5 Ext. or CP 443-1 in PROFINET IO mode |
| ● via interface module | 0 |
| ● Number of pluggable S5 modules (via adapter capsule in central device), max. | 6 |
| Number of IO Controllers |
| ● integrated | 1 |
| ● via CP | 4; Max. 4 in the central controller; no mixed operation of different CP 443-1 types in PROFINET IO mode |
| Number of operable FMs and CPs (recommended) |
| ● FM | Limited by number of slots and number of connections |
| ● CP, PtP | CP 440: Limited by number of slots; CP 441: Limited by number of slots and number of connections |
| ● PROFIBUS and Ethernet CPs | 14; In total max. 10 CPs as DP master and PROFINET controller, of which up to 10 IMs or CPs as DP master and up to 4 CPs as PROFINET controller |
| Slots |
| ● required slots | 1 |
| Time of day |
| Clock |
| ● Hardware clock (real-time) | Yes |
| ● retentive and synchronizable | Yes |
| ● Resolution | 1 ms |
| ● Deviation per day (buffered), max. | 1.7 s; Power off |
| ● Deviation per day (unbuffered), max. | 8.6 s; For power On |
| Operating hours counter |
| ● Number | 16 |
| ● Number/Number range | 0 to 15 |
| ● Range of values | SFCs 2, 3 and 4: 0 to 32767 hours SFC 101: 0 to 2^31 - 1 hours |
| ● Granularity | 1 h |
| ● retentive | Yes |
| Clock synchronization |
| ● supported | Yes |
| ● to MPI, master | Yes |
| ● to MPI, slave | Yes |
| ● to DP, master | Yes |
| ● to DP, slave | Yes |
| ● in AS, master | Yes |
| ● in AS, slave | Yes |
| ● on Ethernet via NTP | Yes; As client |
| ● to IF 964 DP | No |
| Time difference in system when synchronizing via |
| ● Ethernet, max. | 10 ms |
| ● MPI, max. | 200 ms |
| Interfaces |
| Interfaces/bus type | 1 x MPI/PROFIBUS DP, 1 x PROFINET (2 ports) |
| Number of RS 485 interfaces | 1; Combined MPI / PROFIBUS DP |
| 1. Interface |
| Interface type | MPI/PROFIBUS DP |
| Isolated | Yes |
| Interface types |
| ● RS 485 | Yes |
| ● Output current of the interface, max. | 150 mA |
| Protocols |
| ● MPI | Yes |
| ● PROFIBUS DP master | Yes |
| ● PROFIBUS DP slave | Yes |
| MPI |
| ● Number of connections | 32; If a diagnostics repeater is used on the line, the number of connection resources on the line is reduced by 1 |
| ● Transmission rate, max. | 12 Mbit/s |
| Services |
| — PG/OP communication | Yes |
| — Routing | Yes |
| — Global data communication | Yes |
| — S7 basic communication | Yes |
| — S7 communication | Yes |
| — S7 communication, as client | Yes |
| — S7 communication, as server | Yes |
| PROFIBUS DP master |
| ● Number of connections, max. | 16; If a diagnostics repeater is used on the line, the number of connection resources on the line is reduced by 1 |
| ● Transmission rate, max. | 12 Mbit/s |
| ● Number of DP slaves, max. | 32 |
| Services |
| — PG/OP communication | Yes |
| — Routing | Yes; S7 routing |
| — Global data communication | No |
| — S7 basic communication | Yes |
| — S7 communication | Yes |
| — S7 communication, as client | Yes |
| — S7 communication, as server | Yes |
| — Equidistance | Yes |
| — Isochronous mode | Yes |
| — SYNC/FREEZE | Yes |
| — Activation/deactivation of DP slaves | Yes |
| — Direct data exchange (slave-to-slave communication) | Yes |
| — DPV1 | Yes |
| Address area |
| — Inputs, max. | 2 kbyte |
| — Outputs, max. | 2 kbyte |
| User data per DP slave |
| — User data per DP slave, max. | 244 byte |
| — Inputs, max. | 244 byte |
| — Outputs, max. | 244 byte |
| — Slots, max. | 244 |
| — per slot, max. | 128 byte |
| PROFIBUS DP slave |
| ● Number of connections | 16 |
| ● GSD file | http://support.automation.siemens.com/WW/view/en/113652 |
| ● Transmission rate, max. | 12 Mbit/s |
| ● automatic baud rate search | No |
| ● Address area, max. | 32; Virtual slots |
| ● User data per address area, max. | 32 byte |
| — of which consistent, max. | 32 byte |
| Services |
| — PG/OP communication | Yes; with interface active |
| — Routing | Yes; with interface active |
| — Global data communication | No |
| — S7 basic communication | No |
| — S7 communication | Yes |
| — S7 communication, as client | Yes |
| — S7 communication, as server | Yes |
| — Direct data exchange (slave-to-slave communication) | No |
| — DPV1 | No |
| Transfer memory |
| — Inputs | 244 byte |
| — Outputs | 244 byte |
| 2. Interface |
| Interface type | PROFINET |
| Isolated | Yes |
| automatic detection of transmission rate | Yes; Autosensing |
| Autonegotiation | Yes |
| Autocrossing | Yes |
| Change of IP address at runtime, supported | Yes; Assignment by higher-level IO-Controller or by the user program with SFB104 "IP_CONF" |
| Interface types |
| ● RJ 45 (Ethernet) | Yes |
| ● Number of ports | 2 |
| ● integrated switch | Yes |
| Protocols |
| ● PROFINET IO Controller | Yes |
| ● PROFINET IO Device | Yes |
| ● PROFINET CBA | Yes |
| ● PROFIBUS DP master | No |
| ● PROFIBUS DP slave | No |
| ● Open IE communication | Yes |
| ● Web server | Yes |
| ● Point-to-point connection | No |
| ● Media redundancy | Yes |
| PROFINET IO Controller |
| ● Transmission rate, max. | 100 Mbit/s |
| Services |
| — PG/OP communication | Yes |
| — S7 communication | Yes |
| — Isochronous mode | Yes; Only with IRT and the High Performance option |
| — Shared device | Yes |
| — Prioritized startup | Yes |
| — Number of IO devices with prioritized startup, max. | 32 |
| — Number of connectable IO Devices, max. | 256 |
| — Of which IO devices with IRT, max. | 64 |
| — of which in line, max. | 64 |
| — Number of IO Devices with IRT and the option "high flexibility" | 256 |
| — of which in line, max. | 61 |
| — Number of connectable IO Devices for RT, max. | 256 |
| — of which in line, max. | 256 |
| — Activation/deactivation of IO Devices | Yes |
| — Number of IO Devices that can be simultaneously activated/deactivated, max. | 8 |
| — IO Devices changing during operation (partner ports), supported | Yes |
| — Number of IO Devices per tool, max. | 8; 8 parallel calls of the SFC 12 "D_ACT_DP" possible per line. Max. 32 IO Devices changing during operation (partner ports) are supported |
| — Device replacement without swap medium | Yes |
| — Send cycles | 250 μs, 500 μs, 1 ms, 2 ms, 4 ms additionally with IRT with high performance: 250 µs to 4 ms in 125 µs frame |
| — Updating time | 250 µs to 512 ms; minimum value depends on preset communication share for PROFINET IO, on the number of IO Devices and on the amount of configured user data, see PROFINET system description |
| Address area |
| — Inputs, max. | 4 kbyte |
| — Outputs, max. | 4 kbyte |
| — User data consistency, max. | 1 024 byte |
| PROFINET IO Device |
| Services |
| — PG/OP communication | Yes |
| — S7 communication | Yes |
| — Isochronous mode | No |
| — IRT | Yes |
| — Prioritized startup | Yes |
| — Shared device | Yes |
| — Number of IO Controllers with shared device, max. | 2 |
| Transfer memory |
| — Inputs, max. | 1 440 byte; Per IO Controller with shared device |
| — Outputs, max. | 1 440 byte; Per IO Controller with shared device |
| Submodules |
| — Number, max. | 64 |
| — User data per submodule, max. | 1 024 byte |
| PROFINET CBA |
| ● acyclic transmission | Yes |
| ● cyclic transmission | Yes |
| Open IE communication |
| ● Number of connections, max. | 46 |
| ● Local port numbers used at the system end | 0, 20, 21, 25, 80, 102, 135, 161, 34962, 34963, 34964, 65532, 65533, 65534, 65535 |
| ● Keep-alive function, supported | Yes |
| Protocols |
| Redundancy mode |
| Media redundancy |
| — Switchover time on line break, typ. | 200 ms |
| — Number of stations in the ring, max. | 50 |
| SIMATIC communication |
| ● S7 routing | Yes |
| Open IE communication |
| ● TCP/IP | Yes; via integrated PROFINET interface and loadable FBs |
| — Number of connections, max. | 46 |
| — Data length, max. | 32 kbyte |
| — several passive connections per port, supported | Yes |
| ● ISO-on-TCP (RFC1006) | Yes; Via integrated PROFINET interface or CP 443-1 Adv. and loadable FBs |
| — Number of connections, max. | 46 |
| — Data length, max. | 32 kbyte; 1 452 bytes via CP 443-1 Adv. |
| ● UDP | Yes; via integrated PROFINET interface and loadable FBs |
| — Number of connections, max. | 46 |
| — Data length, max. | 1 472 byte |
| Web server |
| ● supported | Yes |
| ● User-defined websites | Yes |
| ● Number of HTTP clients | 5 |
| Isochronous mode |
| Equidistance | Yes |
| Number of DP masters with isochronous mode | 1 |
| User data per isochronous slave, max. | 244 byte |
| shortest clock pulse | 1.5 ms; 0.5 ms without use of SFC 126, 127 |
| max. cycle | 32 ms |
| communication functions / header |
| PG/OP communication | Yes |
| ● Number of connectable OPs without message processing | 47 |
| ● Number of connectable OPs with message processing | 47; When using Alarm_S/SQ and Alarm_D/DQ |
| Data record routing | Yes |
| Global data communication |
| ● supported | Yes |
| ● Number of GD loops, max. | 8 |
| ● Number of GD packets, transmitter, max. | 8 |
| ● Number of GD packets, receiver, max. | 16 |
| ● Size of GD packets, max. | 54 byte |
| ● Size of GD packet (of which consistent), max. | 1 variable |
| S7 basic communication |
| ● communication function / S7 basic communication | Yes |
| ● User data per job, max. | 76 byte |
| ● User data per job (of which consistent), max. | 1 variable |
| S7 communication |
| ● supported | Yes |
| ● as server | Yes |
| ● as client | Yes |
| ● User data per job, max. | 64 kbyte |
| ● User data per job (of which consistent), max. | 462 byte; 1 variable |
| S5 compatible communication |
| ● supported | Yes; Via FC AG_SEND and AG_RECV, max. via 10 CP 443-1 or 443-5 |
| ● User data per job, max. | 8 kbyte |
| ● User data per job (of which consistent), max. | 240 byte |
| ● Number of simultaneous AG-SEND/AG-RECV orders per CPU, max. | 24/24 |
| Standard communication (FMS) |
| ● supported | Yes; Via CP and loadable FB |
| communication functions / PROFINET CBA (with set target communication load) / header |
| ● Setpoint for the CPU communication load | 20 % |
| ● Number of remote interconnection partners | 32 |
| ● Number of functions, master/slave | 150 |
| ● Total of all master/slave connections | 4 500 |
| ● Data length of all incoming connections master/slave, max. | 45 000 byte |
| ● Data length of all outgoing connections master/slave, max. | 45 000 byte |
| ● Number of device-internal and PROFIBUS interconnections | 1 000 |
| ● Data length of device-internal und PROFIBUS interconnections, max. | 16 000 byte |
| ● Data length per connection, max. | 2 000 byte |
| performance data / PROFINET CBA / remote interconnection / with acyclic transfer / header |
| — Sampling interval, min. | 200 ms; Depending on preset communication load, number of interconnections and data length used |
| — Number of incoming interconnections | 250 |
| — Number of outgoing interconnections | 250 |
| — Data length of all incoming interconnections, max. | 8 000 byte |
| — Data length of all outgoing interconnections, max. | 8 000 byte |
| — data volume / as user data for remote interconnections / in the case of acyclic transmission / with PROFINET CBA / per connection / maximum | 2 000 byte |
| performance data / PROFINET CBA / remote interconnection / with cyclic transfer / header |
| — Transmission frequency: Transmission interval, min. | 1 ms; Depending on preset communication load, number of interconnections and data length used |
| — number of remote connections to input variables / with PROFINET CBA / with cyclic transfer / maximum | 300 |
| — number of remote connections to output variables / with cyclical transfer / with PROFINET CBA / maximum | 300 |
| — data volume / as user data for remote interconnections with input variables / with cyclical transfer / with PROFINET CBA / maximum | 4 800 byte |
| — data volume / as user data for remote interconnections with output variables / with cyclical transfer / with PROFINET CBA / maximum | 4 800 byte |
| — data volume / as user data for remote interconnections / with cyclical transfer / with PROFINET CBA / per connection / maximum | 450 byte |
| performance data / PROFINET CBA / HMI variables via PROFINET / acyclic / header |
| — Number of stations that can log on for HMI variables (PN OPC/iMap) | 2x PN OPC/1x iMap |
| — HMI variable updating | 500 ms |
| — Number of HMI variables | 1 000 |
| — Data length of all HMI variables, max. | 32 000 byte |
| performance data / PROFINET CBA / PROFIBUS proxy functionality / header |
| — supported | Yes; 32 PROFIBUS slaves max. connectable |
| — Data length per connection, max. | 240 byte; Slave-dependent |
| Number of connections |
| ● overall | 48 |
| ● usable for PG communication | 47 |
| — reserved for PG communication | 1 |
| — adjustable for PG communication, max. | 0 |
| ● usable for OP communication | 47 |
| — reserved for OP communication | 1 |
| — adjustable for OP communication, max. | 0 |
| ● usable for S7 basic communication | 46 |
| — reserved for S7 basic communication | 0 |
| — adjustable for S7 basic communication, max. | 0 |
| ● usable for S7 communication | 46 |
| — reserved for S7 communication | 0 |
| — adjustable for S7 communication, max. | 0 |
| ● usable for routing | 23 |
| — reserved for routing | 0 |
| — adjustable for routing, max. | 0 |
| S7 message functions |
| Number of login stations for message functions, max. | 47; Max. 47 with Alarm_S/SQ and Alarm_D/DQ (OPs); max. 8 with Alarm, Alarm_8, Alarm_8P, Notify and Notify_8 (e.g. WinCC) |
| Symbol-related messages | Yes |
| SCAN procedure | Yes |
| Program alarms | Yes |
| Process diagnostic messages | Yes |
| simultaneously active Alarm-S blocks, max. | 250; Simultaneously active alarm_S/SQ blocks or alarm_D/DQ blocks |
| Alarm 8-blocks | Yes |
| ● Number of instances for alarm 8 and S7 communication blocks, max. | 300 |
| ● preset, max. | 150 |
| Process control messages | Yes |
| Number of archives that can log on simultaneously (SFB 37 AR_SEND) | 4 |
| Number of messages |
| ● overall, max. | 256 |
| ● in 100 ms grid, max. | 0 |
| ● in 500 ms grid, max. | 256 |
| ● in 1000 ms grid, max. | 256 |
| Number of additional values |
| ● with 100 ms grid, max. | 0 |
| ● with 500, 1000 ms grid, max. | 1 |
| Test commissioning functions |
| Status block | Yes; Up to 16 simultaneously |
| Single step | Yes |
| Number of breakpoints | 16 |
| Status/control |
| ● Status/control variable | Yes; Up to 16 variable tables |
| ● Variables | Inputs/outputs, memory bits, DBs, distributed I/Os, timers, counters |
| ● Number of variables, max. | 70; Status/control |
| Forcing |
| ● Forcing | Yes |
| ● Forcing, variables | Inputs/outputs, bit memories, distributed I/Os |
| ● Number of variables, max. | 64 |
| Diagnostic buffer |
| ● present | Yes |
| ● Number of entries, max. | 3 200 |
| — adjustable | Yes |
| — preset | 120 |
| Service data |
| ● can be read out | Yes |
| Standards, approvals, certificates |
| CE mark | Yes |
| CSA approval | Yes |
| UL approval | Yes |
| cULus | Yes |
| FM approval | Yes |
| RCM (formerly C-TICK) | Yes |
| KC approval | Yes |
| EAC (formerly Gost-R) | Yes |
| Use in hazardous areas |
| ● ATEX | ATEX II 3G Ex nA IIC T4 Gc |
| Ambient conditions |
| Ambient temperature during operation |
| ● min. | 0 °C |
| ● max. | 60 °C |
| configuration / header |
| Configuration software |
| ● STEP 7 | Yes |
| configuration / programming / header |
| ● Command set | see instruction list |
| ● Nesting levels | 7 |
| ● Access to consistent data in process image | Yes |
| ● System functions (SFC) | see instruction list |
| ● System function blocks (SFB) | see instruction list |
| Programming language |
| — LAD | Yes |
| — FBD | Yes |
| — STL | Yes |
| — SCL | Yes |
| — CFC | Yes |
| — GRAPH | Yes |
| — HiGraph® | Yes |
| configuration / programming / number of simultaneously active SFC / header |
| — DPSYC_FR | 2; SFC 11; per interface |
| — D_ACT_DP | 8; SFC 12; per interface |
| — RD_REC | 8; SFC 59; per interface |
| — WR_REC | 8; SFC 58; per interface |
| — WR_PARM | 8; SFC 55; per interface |
| — PARM_MOD | 1; SFC 57; per interface |
| — WR_DPARM | 2; SFC 56; per interface |
| — DPNRM_DG | 8; SFC 13; per interface |
| — RDSYSST | 8; SFC 51 |
| — DP_TOPOL | 1; SFC 103; per interface |
| configuration / programming / number of simultaneously active SFB / header |
| — RDREC | 8; SFB 52; per interface, but not more than 32 across all external interfaces |
| — WRREC | 8; SFB 53; per interface, but not more than 32 across all external interfaces |
| Know-how protection |
| ● User program protection/password protection | Yes |
| ● Block encryption | Yes; With S7 block Privacy |
| Dimensions |
| Width | 25 mm |
| Height | 290 mm |
| Depth | 219 mm |
| Weights |
| Weight, approx. | 750 g |
